Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Plumbing Essentials: A Prerequisite for When Installing a Bathtub
Blog Article
Right here in the next paragraph you will discover a good deal of exceptional facts about How to Install a Bathtub.
Mounting a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably challenging project. If the old bathtub is conveniently obtainable, the project can move rapidly; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to leave the old bathtub and also set in the new one. Make sure you have actually qualified yourself for the job and also fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you might need an expert plumber to make tube links.
This short article will certainly assist you mount a new tub in your restroom if you have currently bought a brand-new bathtub and don't require to alter the plan of your previous water pipelines.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The process of getting rid of the existing taps can be quite problematic due to the limited accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in location between the faucet as well as the sink. Secure the tap in place with the producer supplied backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the tap ends first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wood boards under its feet, position the tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub till the level checks out degree.
To set up taps, fit the bottom of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the bath tub and likewise examine the overflow outlet and the regular outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the bathtub ought to wait until the tub has been made use of a minimum of when as this will certainly resolve it into its last setting.
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final placement.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, bring about complications with dampness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the movement experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the market. It is advisable to fit the tiles using waterproof or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you liked our piece. Sharing is nice. One never knows, you will be doing someone a favor. Thanks for your time. Don't forget to stop by our blog back soon.
Dial, rest easy! Report this page